Locking seat belt




Locking seat belt

Article Navigation:
  • Photo
  • Extend and Retract - How Seatbelts Work | HowStuffWorks
  • Video
  • RELATED PAGES
  • Almost all shoulder belts have a retractor. This device not only spools the excess seat belt, but also locks the seat belt so that it holds you tight in a crash.

    Describe types of retractors. • Locate latchplates and retractors. • Identify approved additional locking steps. • Explain best practices about seat belt systems to.

    In a typical seatbelt system, the belt webbing is connected to a retractor will tighten up, rotating the spool clockwise until there is no more slack in the belt.

    Locking seat belt

    Locking seat belt

    Your options then for a rear facing seat are lower anchors or a seat belt with locking clip. Pretensioners preemptively tighten the belt to prevent the occupant from jerking forward in a crash. The belt shortening clip must be purchased from the vehicle manufacturer, it does not come with the car seat and a locking clip may NOT be used as a substitute. The pawl locks into the gear's teeth, preventing counter-clockwise rotation.

    Locking seat belt

    Locking seat belt

    Locking seat belt

    Locking seat belt

    Locking seat belt

    When to use a Locking Clip - Car Seats For The Littles

    In a typical seatbelt system, the belt webbing is connected to a retractor mechanism. The central element in the retractor is a spool, which is attached to one end of the webbing. Inside the retractor, a spring applies a rotation force, or torque , to the spool.

    This works to rotate the spool so it winds up any loose webbing. When you pull the webbing out, the spool rotates counter-clockwise, which turns the attached spring in the same direction.

    Locking seat belt

    Effectively, the rotating spool works to untwist the spring. The spring wants to return to its original shape, so it resists this twisting motion. If you release the webbing, the spring will tighten up, rotating the spool clockwise until there is no more slack in the belt. The retractor has a locking mechanism that stops the spool from rotating when the car is involved in a collision.

    There are two sorts of locking systems in common use today:. The first sort of system locks the spool when the car rapidly decelerates when it hits something, for example.

    Locking seat belt

    The diagram below shows the simplest version of this design. The central operating element in this mechanism is a weighted pendulum. When the car comes to a sudden stop, the inertia causes the pendulum to swing forward. The pawl on the other end of the pendulum catches hold of a toothed ratchet gear attached to the spool. With the pawl gripping one of its teeth, the gear can't rotate counter-clockwise, and neither can the connected spool.

    When the webbing loosens again after the crash, the gear rotates clockwise and the pawl disengages. The second kind of system locks the spool when something jerks the belt webbing.

    The activating force in most designs is the speed of the spool rotation. The diagram shows a common configuration. The central operating element in this design is a centrifugal clutch -- a weighted pivoting lever mounted to the rotating spool. When the spool spins slowly, the lever doesn't pivot at all. A spring keeps it in position. But when something yanks the webbing, spinning the spool more quickly, centrifugal force drives the weighted end of the lever outward.

    Locking seat belt

    The extended lever pushes a cam piece mounted to the retractor housing. The cam is connected to a pivoting pawl by a sliding pin. As the cam shifts to the left, the pin moves along a groove in the pawl. This pulls the pawl into the spinning ratchet gear attached to the spool. The pawl locks into the gear's teeth, preventing counter-clockwise rotation.

    In some newer seatbelt systems, a pretensioner also works to tighten the belt webbing. In the next section, we'll see how these devices work. A spiraled spring rotates the spool to keep the seatbelt webbing taut.

    How to fix locked seat belt retractor



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲